| QM INDUSTRIES QVPN24V110SEC Mounted Units & Inserts | B:29 mm; Dynamic (Ca):108 kN; Pu:12.200 kN; d2 (max):78.4 mm; s:1.5 mm; r1s (min):2 mm; rs (min):2 mm; d2:55 mm; b:9 mm; E:104.5 mm; |
| QM INDUSTRIES QAAMH15A300SET Mounted Units & Inserts | Sealed Speed Rating n3:6400 rpm; Basic Dynamic Radial Load Rating C:35800 N; D:80.0000 mm; Fillet Radius ra:1.50 mm; Accessories:Without Accessories; Grease Speed Rating Open/Shielded n1:9000 rpm; Basic Static Radial Load Rating Co:19300 N; Oil Speed Rating Open/Shielded n2:11000 rpm; d:25.000 mm; B:21.00 mm; |
| QM INDUSTRIES QMMH15J070SEM Mounted Units & Inserts | Fillet Radius ra:0.08 in; Fillet Radius rb:0.040 in; Oil Speed Rating n2:8000 rpm; d:3.250 in; B:0.7500 in; D:4.7500 in; Basic Static Radial Load Rating Co:46500 N; Basic Dynamic Radial Load Rating C:44900 N; Grease Speed Rating n1:5100 rpm; |
| QM INDUSTRIES QMTU26J130SN Mounted Units & Inserts | Oil Speed Rating Open/Shielded n2:7500 rpm; Fillet Radius ra:1.00 mm; D:85.0000 mm; Basic Static Radial Load Rating Co:32500 N; d:45.000 mm; Accessories:Two Shields & Snap-R; B:19.00 mm; Basic Dynamic Radial Load Rating C:39300 N; Grease Speed Rating Open/Shielded n1:6200 rpm; |
| QM INDUSTRIES QMTU22J110SB Mounted Units & Inserts | Specific static load factor K0:45 N/mm²; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:0.5 m/s; D:12 mm; B:10 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ max.:0.15; Coefficient of friction µ min.:0.08; |
| QM INDUSTRIES QVPG16V212ST Mounted Units & Inserts | L:349.25 mm; P120°:38.3 kN; Initial grease fill:286.33 g; A2:206.375 mm; J1:53.975 mm; Cap bolt:2 x 5/8-11 UNC; Appropriate attachment bolt size G:0.625 in; H:192.484 mm; J min.:263.525 mm; Cap bolt, SAE grade:5; |
| QM INDUSTRIES QAMH15A211SEM Mounted Units & Inserts | da:65 min; Bearing designation:3311 ; ra:2 max; Grease:3 300 min-1; Da:110 max; rs (min):2 mm; Pu:4.909 kN; Weight:2.48 kg; Oil:4 000 min-1; d:55 mm; |
| QM INDUSTRIES QMP08J035SEO Mounted Units & Inserts | d1:44 mm; Fatigue load limit Pu:9.8 kN; C1:0.8 mm; Hexagonal nut:M 24x1.5; Limiting speed:1700 r/min; Recommended tighthening torque:220 N·m; G1:25 mm; B1:49.5 mm; M:8 mm; Basic dynamic load rating C:33 kN; |
| QM INDUSTRIES QVPG19V085ST Mounted Units & Inserts | Grease:5 000 min-1; static Cor:37.700 kN; rs (min):0.6 mm; D1:22 mm; H:14 mm; d:20 mm; D:40 mm; Oil:6 700 min-1; dynamic Cr:24.530 kN; d1:40 mm; |
| QM INDUSTRIES QAAMH15A075SEM Mounted Units & Inserts | End cover:ECW 204; Thread grub screw G2:1/4-28 UNF; Recommended diameter for attachment bolts, inch G:0.375 in; A1:15 mm; T:37.3 mm; Mass bearing unit:0.25 kg; N:12.3 mm; s1:18.3 mm; Housing material:Composite for food a; B4:4.5 mm; |