| QM INDUSTRIES QAMH15A212ST Mounted Units & Inserts | r1,2 min.:3 mm; d3:195 mm; Calculation factor Y0:2.8; b:13.9 mm; d2 ≈:174 mm; Limiting speed:630 r/min; K:7.5 mm; Da max.:256 mm; Ba min.:15 mm; da max.:174 mm; |
| QM INDUSTRIES QVVPN19V080ST Mounted Units & Inserts | Ca min.:7 mm; Calculation factor Y:1.4; da max.:190 mm; ra max.:4 mm; Da min.:252 mm; db min.:177 mm; Cb min.:12 mm; a:53.88 mm; T:52 mm; d1 ≈:215.57 mm; |
| QM INDUSTRIES QAF08A108ST Mounted Units & Inserts | Permissible sliding velocity v min.:0 m/s; Specific dynamic load factor K:140 N/mm²; Tolerance shaft:h8; Permissible sliding velocity v max.:0.5 m/s; Coefficient of friction µ min.:0.03; Mass bushing:1.76 kg; d:190 mm; Specific static load factor K0:200 N/mm²; Coefficient of friction µ max.:0.08; B:150 mm; |
| QM INDUSTRIES QVPG19V303SEC Mounted Units & Inserts | Oil Speed Rating Open/Shielded n2:15000 rpm; Basic Dynamic Radial Load Rating C:12500 N; Basic Static Radial Load Rating Co:8300 N; D:47.0000 mm; B:14.00 mm; Grease Speed Rating Open/Shielded n1:12000 rpm; d:20.000 mm; Accessories:Two Shields; Fillet Radius ra:1.00 mm; |
| QM INDUSTRIES QAMH18A303SET Mounted Units & Inserts | h:52.388 mm; P150°:120 kN; dc:153.988 mm; L:558.8 mm; P120°:133 kN; RG:3/4 NPT; R1:104.775 mm; S:4.763 mm; Cap bolt, SAE grade:8; End plug (suffix Y):EPR 18; |
| QM INDUSTRIES QAATU26A130SEB Mounted Units & Inserts | L:387.35 mm; ba:46.831 mm; Labyrinth ring:2 x LOR 657; RG:3/8 NPT; Stabilizing ring:2 x 38151-24; h:39.688 mm; Cap bolt, SAE grade:5; N1:25.4 mm; A1:111.125 mm; P90°:81.4 kN; |
| QM INDUSTRIES QAMH18A307SN Mounted Units & Inserts | Basic static load rating C0:9.5 kN; D2 ≈:41.55 mm; Calculation factor Y0:0.52; Basic dynamic load rating C:17.4 kN; a:22.8 mm; d2 ≈:26.75 mm; Calculation factor X:0.35; rb max.:0.6 mm; D:52 mm; |
| QM INDUSTRIES QMTU22J407SEN Mounted Units & Inserts | G:M 30x2; l7 min.:34 mm; l1 min.:65 mm; dk:40.7 mm; d:30 mm; Basic dynamic load rating C:62 kN; B:22 mm; d2 max.:75 mm; Material constant KM:330; r1 min.:0.6 mm; |
| QM INDUSTRIES QVPN28V125SEC Mounted Units & Inserts | D1 ≈:67.5 mm; b1:4.5 mm; Limiting speed:5000 r/min; D:80 mm; Da max.:74.8 mm; K:3 mm; Mass bearing:0.76 kg; r3,4 min.:0.3 mm; Basic dynamic load rating C:142 kN; d:50 mm; |
| QM INDUSTRIES QVPG12V055SET Mounted Units & Inserts | Sealed Speed Rating n3:5000 rpm; d:45.000 mm; B:30.20 mm; Grease Speed Rating n1:5000 rpm; Accessories:Shield & Seal; Basic Dynamic Radial Load Rating C:48800 N; D:85.0000 mm; Oil Speed Rating n2:6700 rpm; Fillet Radius ra:1.00 mm; Basic Static Radial Load Rating Co:39000 N; |