| QM INDUSTRIES QVVPN16V211SET Mounted Units & Inserts | B:440 mm; Comparative radial load rating CF:1600 kN; Calculation factor e:0.33; Basic static load rating C0:17000 kN; Calculation factor Y1:2; D:574 mm; r1,2 min.:2.5 mm; Thrust factor K:1.74; Calculation factor Y0:2; Calculation factor Y2:3; |
| QM INDUSTRIES QVPN28V500ST Mounted Units & Inserts | P120°:3800 kN; L:1280 mm; P180°:4200 kN; Cap bolt, size:M 42x300; Appropriate attachment bolt, rec. tightening torque:3640 N·m; J6:1160 mm; Labyrinth seal:2 x TS 92/400; ba max.:243 mm; Appropriate attachment bolt, size G:42 mm; Eye bolt, size:2 x M 48; |
| QM INDUSTRIES QVPG19V303SEC Mounted Units & Inserts | Oil Speed Rating Open/Shielded n2:15000 rpm; Basic Dynamic Radial Load Rating C:12500 N; Basic Static Radial Load Rating Co:8300 N; D:47.0000 mm; B:14.00 mm; Grease Speed Rating Open/Shielded n1:12000 rpm; d:20.000 mm; Accessories:Two Shields; Fillet Radius ra:1.00 mm; |
| QM INDUSTRIES QVPA28V125SEB Mounted Units & Inserts | B:22.20 mm; Basic Dynamic Radial Load Rating C:22900 N; Oil Speed Rating n2:11000 rpm; d:25.000 mm; Grease Speed Rating n1:8000 rpm; Accessories:Two Seals & Snap-Rin; D:52.0000 mm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:8000 rpm; Basic Static Radial Load Rating Co:21200 N; |
| QM INDUSTRIES QVVPG14V060SB Mounted Units & Inserts | Mass bearing (including seat washer where applicable):5.6 kg; r1,2 min.:1 mm; ra max.:1 mm; Reference speed:1100 r/min; Fatigue load limit Pu:16.6 kN; Basic dynamic load rating C:125 kN; d1 ≈:458.5 mm; Minimum load factor A:4; d:420 mm; Basic static load rating C0:880 kN; |
| QM INDUSTRIES QVVPA28V500SO Mounted Units & Inserts | Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ min.:0.05; Permissible sliding velocity v max.:5 m/s; Mass bushing:0.005 kg; B:12 mm; Tolerance shaft:h8; Coefficient of friction µ max.:0.1; Specific dynamic load factor K:10 N/mm²; Tolerance housing:H7; Specific static load factor K0:20 N/mm²; |
| QM INDUSTRIES QMTU26J415SM Mounted Units & Inserts | D1:130 mm; a:2.5 mm; B:50 mm; Tolerance shaft:e7; Specific dynamic load factor K:25 N/mm²; Mass bushing:1.65 kg; Permissible sliding velocity v min.:0 m/s; h:101.5 mm; d:100 mm; Permissible sliding velocity v max.:0.5 m/s; |
| QM INDUSTRIES QVVPG19V304SEB Mounted Units & Inserts | Lock nut:N 09; Lock washer:W 10; Threads per inch:18; Hydraulic nut:HMVC 10E; B:11.379 mm; B4:14.173 mm; Mass adapter sleeve assembly:0.33 kg; Sleeve:S 10x1.1/2; d3 max.:64.414 mm; G:49.962 mm; |
| QM INDUSTRIES QMTU22J110SB Mounted Units & Inserts | Specific static load factor K0:45 N/mm²; Tolerance housing:H7; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:0.5 m/s; D:12 mm; B:10 mm; Mass bushing:0.0066 kg; Tolerance shaft:e7; Coefficient of friction µ max.:0.15; Coefficient of friction µ min.:0.08; |
| QM INDUSTRIES CKDR303 Mounted Units & Inserts | d1 ≈:56.9 mm; T:29.37 mm; Basic dynamic load rating C:86.5 kN; B:27.783 mm; db min.:39.5 mm; Ca min.:3 mm; Db min.:69 mm; Mass bearing:0.62 kg; Calculation factor Y:1.1; Limiting speed:9000 r/min; |