| QM INDUSTRIES QVPG14V060SB Mounted Units & Inserts | da:85.725 mm; S:4.763 mm; P120°:64.9 kN; H2:44.45 mm; J max.:333.375 mm; End plug (suffix Y):EPR 15; Bearing:22220 EK; Ca:55.804 mm; N1:22.225 mm; Stabilizing ring:SR-20-17; |
| QM INDUSTRIES QMMH15J215SEN Mounted Units & Inserts | B1:73 mm; Fatigue load limit Pu:48 kN; b:8.3 mm; d1:65 mm; Calculation factor Y1:1.9; Calculation factor Y2:2.9; Basic static load rating C0:475 kN; K:4.5 mm; da max.:92 mm; D:160 mm; |
| QM INDUSTRIES QMFY08J035SN Mounted Units & Inserts | Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:6000 rpm; Basic Static Radial Load Rating Co:20000 N; Accessories:Synthetic Rubber Sea; d:35.000 mm; Basic Dynamic Radial Load Rating C:36400 N; D:80.0000 mm; B:34.93 mm; Oil Speed Rating Open/Shielded n2:10000 rpm; Grease Speed Rating Open/Shielded n1:8500 rpm; |
| QM INDUSTRIES QVVPG12V055SEC Mounted Units & Inserts | with tapered bore:420 min-1; Dynamic (Cr):12 mm; Pu:3210 kN; Grease:6410 kN; d:440 mm; Static (Cor):22.3 mm; rs (min):6 mm; with cylindrical bore:350 min-1; D:650 mm; Oil:464.980 kN; |
| QM INDUSTRIES QMTU26J415SB Mounted Units & Inserts | Fillet Radius ra:2.50 mm; D:190.0000 mm; d:75.000 mm; B:82.60 mm; Grease Speed Rating n1:2200 rpm; Basic Dynamic Radial Load Rating C:212000 N; Basic Static Radial Load Rating Co:200000 N; Oil Speed Rating n2:3200 rpm; |
| QM INDUSTRIES QVPG16V070SEB Mounted Units & Inserts | Mass rod end:1.3 kg; Material constant KM:330; h:130 mm; B:25 mm; l2 max.:174 mm; l1 min.:68 mm; Basic dynamic load rating C:80 kN; Specific dynamic load factor K:100 N/mm²; dk:47 mm; α:6 °; |
| QM INDUSTRIES QAF08A108SEM Mounted Units & Inserts | d:80.000 mm; Oil Speed Rating n2:3800 rpm; Basic Static Radial Load Rating Co:95000 N; Basic Dynamic Radial Load Rating C:106000 N; Grease Speed Rating n1:2800 rpm; B:44.40 mm; D:140.0000 mm; Accessories:Two Seals; Fillet Radius ra:2.00 mm; Sealed Speed Rating n3:2800 rpm; |
| QM INDUSTRIES QMTU26J500SEM Mounted Units & Inserts | Basic static load rating C0:7.8 kN; A5:18 mm; T:40 mm; Recommended diameter for attachment bolts, mm G:10 mm; A1:15 mm; Fatigue load limit Pu:0.335 kN; A3:3.2 mm; d:25 mm; Recommended diameter for attachment bolts, inch G:0.375 in; Hexagonal key size for grub screw N:2.5 mm; |
| QM INDUSTRIES QVPN28V500ST Mounted Units & Inserts | P120°:3800 kN; L:1280 mm; P180°:4200 kN; Cap bolt, size:M 42x300; Appropriate attachment bolt, rec. tightening torque:3640 N·m; J6:1160 mm; Labyrinth seal:2 x TS 92/400; ba max.:243 mm; Appropriate attachment bolt, size G:42 mm; Eye bolt, size:2 x M 48; |
| 2.188 Inch | 55.575 Millimeter x 3.12 Inch | 79.248 Millimeter x 2.5 Inch | 63.5 Millimeter QM INDUSTRIES QMPL11J203SEM Pillow Block Bearings | Basic Static Radial Load Rating Co:73500 N; d:65.000 mm; Fillet Radius ra:1.50 mm; B:38.10 mm; D:120.0000 mm; Basic Dynamic Radial Load Rating C:80600 N; Sealed Speed Rating n3:3600 rpm; Accessories:Two Seals & Snap-Rin; Grease Speed Rating n1:3600 rpm; Oil Speed Rating n2:4800 rpm; Size (mm):2.188 Inch | 55.575 Millimeter x 3.12 Inch | 79.248 Millimeter x 2.5 Inch | 63.5 Millimeter ; |